Woah federation would be huge!
Someday I would love to be able to share and receive shared photos / albums to and from users on different servers. Especially if it lets me sync the original files so that I can keep a copy in case their server goes down. It would also be neat if you could enable activitypub so that your account could show up as a fediverse user that people can follow for public or approved follower only posts, pixelfed compatibility would be super cool.
Unironically why I switched my parents to Linux - they don’t touch any important settings so usually the only problems are when they get a new popup / prompt they’ve never seen, which ofc happens a lot more on windows especially when they decide to push some new thing or decide that they want to convince people to enable something new or change a setting that they want people to use.
I also love that if they call me I can just ssh in over tailscale and do whatever needs doing.
Seconding immich - I host it for my family which makes sharing vacation photos easy since they all have accounts on my instance that can be shared to / from.
Keep in mind that if you set up raid using zfs or btrfs (idk how it works with other systems but that’s what I’ve used) then you also get scrubs which detect and fix bit rot and unrecoverable read errors. Without that or a similar system, those errors will go undetected and your backup system will backup those corrupted files as well.
Personally one of the main reasons I used zfs and now btrfs with redundancy is to protect irreplaceable files (family memories and stuff) from those kinds of errors, as I used to just keep stuff on a hard drive until I discovered loads of my irreplaceable vacation photos to be corrupted, including the backups which backed up the corruption.
If your files can be reacquired, then I don’t think it’s a big deal. But if they aren’t, then I think having scrubs or integrity checks with redundancy so that issues can be repaired, as well as backups with snapshots to prevent errors or mistakes from messing up your backups, is a necessity. But it just depends on how much you value your files.
Ah, I didn’t gather that you were implying that they were doing a partial enforcement so I was confused.
I don’t have strong opinions about BlueSky (I have an account, I prefer activitypub but it’s whatever), but to me I will view it as centralized until someone who is not BlueSky runs a second relay server that is federated with the BlueSky run one.
And based on the writings of one of the creators of activitypub, Christine Lemmer-Webber, there are some hurdles to that happening: https://dustycloud.org/blog/how-decentralized-is-bluesky/
They don’t appear to be labeling in both the display name and bio, just the bio, so aren’t they breaking the rule?
From my perspective, plenty of people are pointing it out. One of the authors of activitypub Christine Lemmer-Webber talked about it in depth in a blog post: https://dustycloud.org/blog/how-decentralized-is-bluesky/
So it’s basically as federated as a fediverse server with federation turned off lmao
Wouldn’t that only work if your neighbors tv was plugged into Ethernet so that the wifi chip can be free to start a hotspot? I can’t find any info about that so I’m not sure.
I recently got a waterdrop brand RO filter, which I think will help reduce scale a lot in my espresso machine and probably make descaling faster / easier. I also love basically having no scale build up in my humidifier. My TDS goes from about 100 to 3 or 4 according to the readout on the faucet and my handheld meter. I’m biased though because they accidentally refunded me so I basically got it for free.
I got a “refurbished” G3P800 which looked identical to new and was significantly cheaper than MSRP, so I would check out what they have refurbished on their site or sold through their official store on eBay. They’re also on Amazon I’m sure, but I avoid Amazon.
If you choose their cheaper models like the G2 and get a refurbished one they go pretty cheap like just under $200
I still have a smart TV so I don’t need to have a non smart tv. But I refuse to use smart features for several reasons:
I mostly watch stuff downloaded to my Plex, so a PC running Plex htpc / desktop or any android box (Nvidia shield is pretty good) with the Plex or jellyfin app is all I need. I also like that I can easily watch YouTube through a browser with ad block and sponsorblock (I think smarttube does that for Android boxes like the shield)
I also game on the PC so I guess you could consider it a game console for the purposes of categorizing the use case.
The nice thing about Samsungs is that basically all their remotes work with all their TVs, so I just found one without the smart button so I can’t tell that mine is smart, and I obviously never connected it to internet. I think it’s a lot cheaper than trying to get a commercial dumb TV too.
Just tossing some more ideas in the ring:
Make sure there isn’t a piece of plastic stuck to the heater under the bed - happened to me a couple times and it causes a very sudden high spot that manifests as a very thin spot on the first layer or a hole if it’s bad enough.
If your bed is PEI, I find that fresh from a dish soap wash or isopropyl wipe down isn’t always the best adhesion - but I find that printing just the first layer and then peeling and restarting can give an even better adhesion since the first layer picks up any contaminants very well, but that doesn’t seem likely to be the root cause here.
Are you able to watch up close while it prints the first layer? You should be able to see whether the plastic is still coming out of the nozzle when it hits the bad spot. You should also be able to easily see if the plastic is still coming out but balling up on the nozzle, or if it’s getting squished too much and having trouble due to a high spot, or if it stopped extruding for a moment and only pulled the last bit of extrusion into a thin hair while not pushing out any new filament even though there’s space under the nozzle. That will help narrow down the issue a lot between a bed leveling issue, adhesion issue, nozzle clog issue, or other extrusion issue.
Just looking at the picture, because it happens around the same spot as it goes back and forth, it feels more like something around that spot on the bed - either a high spot or a dirty spot. But watching what happens up close and how the filament coming out up close behaves should help determine.
It looks like the orange thing on the top pushes the phone forwards when pressed.
Gotcha, currently I just pay $5/mo for mullvad but I’ve considered adding usenet to the mix in case it can find a few missing episodes here and there. But I would be basically doing that only for my friends because all of the stuff I watch is popular, recent, and on streaming sites so I don’t have any issues finding it on public indexers.
Doesn’t usenet usually cost money too though? I see them as about equivalent, it’s just that I already need a VPN to access certain porn sites in my state so I might as well use the same subscription and torrent for free instead of adding another cost.
This is the main reason I always preferred running my own arrstack over paying for realdebrid. Besides mullvad VPN going out of business suddenly (which wouldn’t be that hard to switch) or taking down all torrent indexes simultaneously, there is no service that can be taken down using the law that would interrupt my media consumption. And even if all torrent sites went down tomorrow, I can trivially hook back up my arrstack to a dht crawler and ill be basically fully decentralized, pulling infohashes from the ether and downloading using purely P2P technologies with no (practical) central point of failure.
In addition to the possibility of reinforcement bars it could also have to do with the thickness of the tactile pad or it could have recessed spots underneath (to save on material if it was injection molded) that could create an insulating air gap.
I once had someone open an issue in my side project repo who asked about a major release bump and whether it meant there were any breaking changes or major changes and I was just like idk I just thought I added enough and felt like bumping the major version ¯\_(ツ)_/¯