Staining red oak for a slat wall around our fireplace. Hope to get it installed this week.

That doesnt sound fun at all. Would a drain snake work?

Edit: responding to @jarfil@beehaw.org. Sorry, still getting used to the Connect app.

Was going to try to get the rust off my father’s crappy old hand plane (since restoring it would get me out of having to buy a hand plane of my own for now), but it doesn’t look like I’m going to get that far this week. Spent a couple of hours moving books around to clear some shelf space instead.

Edit: Turned out that my actual DIY for the weekend was fixing my computer mouse, which suddenly developed a tendency to jump the cursor randomly to the upper-left corner of the screen. Turns out that it’s possible to kill a laser mouse with cat hair if you get enough of it wedged into the little opening on the bottom of the mouse that the laser shines through. And here I thought fluff was only a failure mode for ball mice.

I’m still building the addition to my wood framed green house, still have a couple of weekends to go till its done.

Reattaching my towel rack to my wall. It was held in with drywall anchors but those have failed so will either repatch and reattach or glue it back on. Depends on how done with it I am

was going to make a small garden in a wood box on the deck of my apartment, but its getting unusually hot i think i’ll put it off for a little longer

Going to be resealing our countertops today. Shouldn’t be too complicated, but it’s my first time doing it so we’ll see.

Installing a new sink and dishwasher, here’s to not flooding the place. Probably.

I recently finished my butcher block desk and enjoyed it so much I asked for a bunch of wood working tools as birthday gifts. I don’t usually care about my birthday or gifts, but it’s always an ordeal for my family because they insist. So this year I finally told them to get the wood working basics.

I’m eyeing my second project now and trying not to tell myself that it should be the new coffee table that we’ve needed for the past 3 years. That feels like a more advanced project, but it’s so tempting.

I need to tighten the bolts on the kids toilet, lol. Otherwise just running a ton of errands (none DIY-related).

I did get around to the hand plane this week. Most of the rust and grot is off and now I need to lap the sole as best I can.

If there’s still a bit of rust left somewhere . . . I don’t actually care. It’s a 1970s Canadian-made Stanley Craftsman plane, which means that it’s effectively worthless. I just want it in good enough shape not to leave rust streaks on whatever I’m trying to plane. In five years or so, I expect I’ll either have given up on woodworking or bought a higher-quality replacement.

(I also need to fix a chair, which I didn’t quite get to today.)

Starting the refinish job on our front porch. Got my broom and sander and some dry weather in the forecast, hopefully it’ll be finished before the next storm rolls through!

deleted by creator

Probably going to practise using my new laser cutter/engraver I just got last week.

Trying to fix a slow bathtub drain.

It’s got one of those flexible ribbed pipes that keeps holding onto everything, and whoever installed the bathtub had the amazing idea of fully encasing it in brick and large tiles, with no access left to replace the pipe. To add insult to injury, the pipe is attached to the bathtub by a single screw going through a metal strainer, so no way to properly shove in a pipe cleaner without it coming detached and falling under the bathtub… inside the encased part; even if I managed to fish it out afterwards, no way it’s going to match the gasket again. The toilet is also so close to it, that even to try breaking the tile and brick to get to the pipe, one would have to remove the toilet first.

I’ve poured in some “gel drain cleaner”, left it for a while, washed it out, and some plunger action seemed to move some stuff around, but it was still slow. Poured some caustic soda, which outgassed pretty nicely, and the plunger worked some more, but I’d say it’s still less than 50% there.

I’m torn as to what to try next, whether some HCl, bleach, or sulfuric, but the strainer is metal and I don’t want to make it look worse than it already does. Could try more of the gel and/or soda, but I think they might’ve already done all they were to do.