I am stripping and re-sealing a corner shower stall, and am having a hell of time removing all the old caulk. I also discovered the previous homeowners decided to just caulk over the previous caulk that was on there, so I am removing 2 or 3 layers depending on the location. It was leaking in the spots that had 3 layers so I think they just added more caulk to “fix” leaks. I have the chemical caulk remover, and that certainly helps, but it still is taking a metric fuck-ton of manual labor. Any tricks/suggestions for removal of very old caulk? I am about to throw a scotch brite on a palm sander and go to town.

  • Shdwdrgn@mander.xyzEnglish
    7·
    1 year ago

    Afraid I can’t offer any tricks, and unfortunately I will be doing this task myself soon. However one thing that concerns me about you seeing leaks is that if there is a full pan in the bottom, that pan should have a lip on it that goes up behind (and higher than) the edge of the tile. This means any water at the height of the caulk should not be causing a leak. Is it possible that the mess of caulking you are seeing is due to a previous owner attempting to cover over actual holes in the pan?

    I had a plumber out to look at my basement shower right before Christmas. The drain was backing up and we couldn’t get it to clear, but even when running the water slowly (nothing appearing to come back up the drain) I was seeing water running out onto the floor after a couple minutes. Well it turns out there is supposed to be a seal between the drain pipe and the larger pipe that drops down from the pan. My seal was completely missing so the water was running onto the packed earth under my cement floor and then backing up underneath the shower pan. He told me I could seal this with silicone and this has been working just fine so far, but I’ve also found rubber seals I can buy to hammer into place for a more permanent seal next time it fails. Not sure if any of this helps with your situation, but I figure good knowledge should be passed around!

    • Vodulas [they/them]@beehaw.orgOP
      4·
      1 year ago

      Fortunately I know where the leak was coming from. It is where the surround meets the glass front and pan. The surround is plastic, not tile, and was clearly leaking from the corner.

      • Shdwdrgn@mander.xyzEnglish
        4·
        1 year ago

        Best of luck to you then!

        I did think of one thing I’ve seen at the hardware store… they make a tool with a triangular tip, which I believe was for removing caulking from corners. You might take a look for one of those?

        • Vodulas [they/them]@beehaw.orgOP
          2·
          1 year ago

          I have a plastic version, and it was great until it was no longer sharp. I’ll be picking up the one posted by JimmyBigSausage. Seems pretty versatile

  • CaptObvious@literature.cafe
    7·
    1 year ago

    Are you sure that the older layers are caulk and not grout? If it’s actually grout, you can use a chisel to gently break it up.

  • navigatron@beehaw.org
    6·
    1 year ago

    Removing caulk sucks.

    The best tool for the job is a razor blade / utility knife, and a pack of replacement blades. Blades are dirt cheap, don’t be afraid to bend them / abuse them.

  • Seathru@beehaw.orgEnglish
    3·
    1 year ago

    What’s under the caulk? If it’s ceramic tile, you can probably get away with a brass cup brush in a drill. Test in an inconspicuous area first obviously, but it should be less likely to scuff up the surface as something like scotchbrite.

      • Seathru@beehaw.orgEnglish
        3·
        1 year ago

        Brass brush on a drill would probably melt into plastic fast. But a handheld one would work ok, or steel if you need more persuasion and aren’t worried about scratches.

  • Dave.@aussie.zone
    2·
    1 year ago

    If you’ve got a heat gun, a moderate amount of heat for 30 seconds or so can help. Just go easy on the heat if you’ve already applied a chemical remover, don’t want to gas yourself.